欢迎光临济南九创门业有限公司官网!

联系我们 收藏本站 在线留言

新闻资讯

首页>>新闻资讯>>车库门定期保养需注意6点事项?
新闻资讯
联系我们
济南九创门业有限公司

联系人:李经理

电话:15006519345

网址:www.xlmygs.com

地址:济南市天桥区北园大街372号大明家居3F-A-10

车库门定期保养需注意6点事项?

来源:http://www.jnhsjlm.com 日期:2020-07-14 发布人:guanli
  1.检查弹簧
  1. Check the spring
  在上掀门上,每一面的弹簧都挂在槽中。将弹簧钩移至相邻的槽中,调整其弹力。在卷帘门上,每一面的弹簧均由滑轮上的弹簧式缆线控制。为了调整弹簧的弹力,请将经过门上方平板的缆线拉长,然后在末端重新打结,以保持新的弹力。警告:如果卷帘门只在门有一个扭转弹簧,请不要尝试修理它。因为那弹簧的弹力实在是太大了,可能会使您受伤。对于使用了这种弹簧的门,应当打电话向维修服务部门求助
  On the liftgate, springs on each side hang in the slots. Move the spring hook to the adjacent slot and adjust its spring force. On the rolling shutter door, the spring on each side is controlled by the spring type cable on the pulley. In order to adjust the spring force, lengthen the cable passing through the flat plate above the door, and then tie the knot again at the end to maintain the new spring force. Warning: if a rolling shutter door has only one torsion spring in the center of the door, do not attempt to repair it. Because the spring is so strong that it may hurt you. For doors that use this spring, you should call a professional maintenance service department for help
  2.将所有变松的螺丝拧紧
  2. Tighten all loose screws
  请查找变松的部件,并根据需求上紧。在上掀门上,检查安装弹簧的平板,确保螺钉已经旋紧,并将变松的螺钉拧紧。在卷帘门上,请检查将门的各个部分固定在一起的铰链,将所有变松的螺钉拧紧,并更换受损的铰链。门有时向一侧下沉,这个问题往往可以通过维修铰链来纠正。如果螺钉孔变大了,请换一根直径相同但更长的螺钉,在一根空心纤维棒上涂木工胶,然后套在新螺钉上。如果铰链处的木料出现裂缝,请拆掉铰链,将木料填孔剂填在裂缝和螺钉孔中。待填孔剂干燥后再更换铰链。如果可能,请将铰链移到实心木料上。
  Please find the loose parts and tighten them as required. On the upper lift door, check the spring plate to make sure that the screws have been tightened and tighten the loosened screws. On roller shutter doors, check the hinges that hold the various parts of the door together, tighten all loose screws, and replace damaged hinges. Doors sometimes sink to one side, which can often be corrected by repairing the hinges. If the screw hole becomes larger, replace a screw with the same diameter but longer, coat a hollow fiber rod with wood glue, and then put it on the new screw. If there are cracks in the wood at the hinge, remove the hinge and fill the crack and screw hole with wood filler. Replace the hinge after the filling agent is dry. If possible, move the hinge to the solid wood.
            济南车库门
  3.确保轨道是否在水平线上
  3. Make sure the track is on the horizontal line
  用水平仪检查轨道,确保轨道在同一水平线上。水平轨道应当略向车库后部倾斜,如果是卷帘门,轨道的纵向部分应精确垂直。在车库的墙壁上,两条轨道必须处于同一高度,如果轨道没有准确对齐,请将固定安装支架的螺钉或螺栓拧松,但不要把它们取下来,然后小心地敲打轨道,使它们移动到适当的位置。用水平仪重新检查轨道,确保它们处于正确的位置,然后将安装支架上的螺钉或螺栓拧紧。
  Check the track with a level to ensure that the track is on the same level. The horizontal track should be slightly inclined to the rear of the garage, and in the case of rolling shutter doors, the longitudinal part of the track should be exactly vertical. On the wall of the garage, the two rails must be at the same height. If the rails are not correctly aligned, loosen the screws or bolts that fix the mounting bracket, but do not remove them, and then carefully tap the rails to move them into place. Recheck the rails with a spirit level to make sure they are in the correct position, and then tighten the screws or bolts on the mounting bracket.
  4.检查金属轨道
  4. Check the metal track
  检查车库内部的金属轨道,查看将轨道固定到墙壁的安装支架。如果支架松了,请拧紧螺栓或螺钉。将车库门关上,在车库内部检查轨道是否有凹陷、弯曲或变平的地方,如果有任何损坏之处,请用橡皮锤,或用一块废木料垫着锤子敲打这些地方。如果轨道严重损坏,您必须更换。
  Check the metal rails inside the garage to see the mounting brackets that hold the rails to the wall. If the bracket is loose, tighten the bolts or screws. Close the garage door and check the track inside the garage for dents, bends, or flattening. If there is any damage, tap these places with a rubber hammer or a piece of wood cushion. If the track is seriously damaged, you must replace it.
  5.在轨道上喷洒润滑油
  5. Spray lubricating oil on the track
  将石墨粉撒在轨道上,将家用润滑油或硅树脂喷在转轴上,或者在轨道和转轴上喷洒车库门专用润滑油喷剂,以起到润滑作用。如果有滑轮,请您使用和用在转轴上的相同的润滑剂润滑。
  Sprinkle graphite powder on the track, spray household lubricating oil or silicone resin on the rotating shaft, or spray special lubricating oil spray for garage door on the track and shaft to play a lubricating role. If there are pulleys, please use the same lubricant as used on the shaft.
  6.将轨道污垢去除干净
  6. Remove the track dirt
  用高浓度家用清洁剂清洗轨道,去除污垢和硬化的油脂。将转轴彻底清洗干净,然后将轨道和转轴擦干。
  Clean the track with a high concentration of household cleaner to remove dirt and hardened grease. Clean the shaft thoroughly, then dry the track and shaft.

推荐阅读/ Recommended reading

车库门门板材料厚度很重要 现在的车库门大多是用铝合金材料作为而成的,车库门的厚度往往决定了整个车库门的质量的好坏。现如今大多数的车

车库门维修有哪些方法? 2021-05-13
如何对车库门电机进行日常保养维护? 2021-05-07
日常使用翻板车库门的五个好处? 2021-05-05
验收防火车库门的外观要求? 2021-04-30

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

  • 济南九创门业有限公司