• 联系人:李经理
  • 手机:15006519345/18754165377
  • 网址:http://www.xlmygs.com
  • 地址:济南市金牛建材市场
新闻中心当前位置:首页-新闻动态
    济南车库门(电动)行程间距如何调理更标准
    来源:http://www.xlmygs.com  日期:2019-06-04 17:01:00
    济南车库门(电动)行程间距如何调理更标准
    How to adjust the distance of Jinan garage door (electric) more standard电动车库门的行程间隔不精确会影响到电动车库门的运用,找专业的车库门厂家调整需求的费用会很多,因而,本人手动停止调整也是能够的。电动车库门行程间隔的调整按以下步骤停止即可。
    The imprecise travel interval of the electric garage door will affect the use of the electric garage door. It will cost a lot to find a professional garage door manufacturer to adjust the demand. Therefore, it is also possible for me to stop adjusting manually. The adjustment of the travel interval of the electric garage door can be stopped by following steps.
    1、按下控制板上的FUNC键,此时RUN灯开端闪动,按住此键超越8秒,RUN灯变为常亮,此时程序进入开关门行程和过载力学习过程;2、按INC键时 电机开端向开门的方向运转,按住不放,电机运转速度由慢转快,同时RUN指示灯闪亮,标明电机向上运转。抵达理想的位置后松开按键,电机中止运转;假如按下DEC键,则电机由慢转快向关门方向运转,STA灯闪亮。用这两个按键可调理上行位置。
    1. Press the FUNC key on the control board, then the RUN light starts to flicker. Press and hold this key for more than 8 seconds, and the RUN light becomes constant. At this time, the program enters the learning process of switching and overloading. 2. When press the INC key, the motor starts to run in the direction of opening, press and hold, and the speed of the motor turns from slow to fast. At the same time, the RUN light flashes, indicating that the motor runs upward. After reaching the ideal position, release the button, and the motor will stop running. If the DEC key is pressed, the motor will turn from slow to fast to close, and the STA lamp will shine. Use these two keys to adjust the upstream position.
    济南车库门

    Jinan Garage Gate

                              济南车库门

    3、假如上行位置调整适宜后,按FUNC键一次,则RUN指示灯快速闪烁后熄灭,标明上到位学习完成;同时STA指示灯点亮,程序进入下到位学习过程;4、用 INC 和 DEC两个按键调整下到位位置,在抵达预定位置后,按FUNC键一次,STA灯闪亮,标明下到位完成;5、上下到位位置调整终了,程序自动进入开关门力气:门体首先向开门的方向运转,同时RUN灯点亮,在门体运转过程中,程序自动丈量运转中门体所遭到的阻力,抵达上到位后自动中止,延时一段时间后,程序自动关门,此时STA灯点亮,程序丈量关门时的力气,抵达下到位后,自动中止;6、按遥控器上的按键或墙壁开打开的按键,电机依照请求正常运转。
    3. If the upstream position is adjusted properly, press the FUNC key once, then the RUN indicator flashes quickly and then goes out, indicating that the upper-position learning is completed; at the same time, the STA indicator lights up and the program enters the lower-position learning process; 4. Adjust the lower-position with the INC and DEC keys, and press the FUNC key once after reaching the predetermined position, the STA lamp flashes, indicating that the lower-position is completed; 5. Upper-lower-position learning is completed; At the end of the position adjustment, the program automatically enters the power of the door: the door body first moves towards the direction of opening, and the RUN lamp lights up. In the process of the door body operation, the program automatically measures the resistance of the door body in operation, automatically stops after reaching the upper position, and automatically closes the door after a delay period of time. At this time, the STA lamp lights up, the program measures the force of closing the door, after reaching the lower position. 6. Press the button on the remote controller or open the button on the wall, and the motor will run normally according to the request.